Call Of Duty · FPS
Killer v1.1
By Unknown
Killer v1.1 is a Call Of Duty Cronus Zen script featuring two profiles (primary and secondary) for any weapon category., switch profile as you switch weapons in game., if game weapon and oled weapon are unsynced, and use profile quick toggle., built for PC,Ps4,Ps5,Xbox,Xbox One,Xbox Series,Switch.
premium
$40.00
Updated 2026-03-25T16:59:36.719Z
Platform
PS5, Xbox, PC, Switch
Difficulty
beginner
Compatibility
Latest Season
Overview
Below is the same content, reorganized into two sections — Features / Description and Guide — using clean bulleted lists and h4 as the largest header. Wording is kept as close as possible to the original while making it cleaner. Features Profiles Two profiles (Primary and Secondary) for any weapon category. Switch profile as you switch weapons in game. If game weapon and OLED weapon are unsynced, use profile quick toggle. Temporary Values Each profile has temporary values for fine-tuning AntiRecoil or Rate of Fire. Temp Val is added to or subtracted from pre-stored values. Temp Val is profile-dependent; reset if you change the weapon. Hold CROSS/A for 500 ms in ModWeapon to reset Temp Val. Private Features (Profile-Specific Values) AntiRecoil type per profile (Progressive, Standard, Rumble) Progressive: Start, End, Time values for advanced recoil control. Standard: Adjustable vertical and horizontal values. Rumble: Same adjustment logic as Standard but based on controller vibration. RapidFire with private toggle and private Rate of Fire. BurstFire with private toggle, global value. AIM Assist (Polar Assist with TaylorDrift Shapes) with private toggle, global values. StrafeShot with private toggle, global value. Global Features (Global Values Shared Across Profiles) DynaSens (Dynamic Sensitivity) Slider (slide when pressing forward) Swap Trigger/Bumper Inverted Y (vertical AntiRecoil) Additional Global Features Auto ADS Rumbles (controller vibration disable) Slide Cancel (beta; requires Tac Sprint) Snake Sprint (beta; requires Tac Sprint) S Walk (beta; requires Tac Sprint) YY Swap Auto Reload Additional Utility Features KillSwitch (disables the script) Hair Trigger Speed Toggle (quick access to four mods) VM Control (sets virtual machine speed) Default 10ms = 0 Xbox One 8ms = 1 PS4 6ms = 2 PS5 4ms = 3 Xbox Series 2ms = 4 PC 1ms = 5 AIM Assist Details Radius controls size of micro-movements (larger = more screen shake). Steps controls frequency. With Batts Sticky: lower Steps may slow movement. With other shapes: higher Steps may slow movement. Strafe Details Strafe Shot: strafes while firing. Cut Strafe: left stick directional strafe while holding R2 (not compatible with AutoADS). Cut Strafe with camera movement (not compatible with AutoADS). Dynamic Sensitivity Details DS Initial Sens: sensitivity while aiming before increase. DS Limit: stick input point where sensitivity begins increasing. DS Restart: point where sensitivity resets back to initial. DS Max Sens: max sensitivity allowed. DS Increase Rate: determines speed of sensitivity increase.
What Is Included
- [object Object]
- [object Object]
- [object Object]
- [object Object]
How Killer v1.1 Works
Killer v1.1 works by sending optimized input signals through your Cronus Zen to your PC,Ps4,Ps5,Xbox,Xbox One,Xbox Series,Switch controller. The script adjusts two profiles (primary and secondary) for any weapon category., switch profile as you switch weapons in game., if game weapon and oled weapon are unsynced, use profile quick toggle. based on the parameters you configure in Zen Studio. Each feature can be tuned independently, so you can enable only what you need. The profile is designed around Call Of Duty's current mechanics and is validated against Latest Season.
Compatibility Matrix
| Requirement | Status |
|---|---|
| Game target | Call Of Duty |
| Platform | PC,Ps4,Ps5,Xbox,Xbox One,Xbox Series,Switch |
| Device | Cronus Zen |
| Compatibility target | Latest Season |
| Last tested | 2026-03-06 |
Compatibility Notes
Killer v1.1 targets Call Of Duty on PC,Ps4,Ps5,Xbox,Xbox One,Xbox Series,Switch and is tested for Latest Season. The script runs on Cronus Zen hardware. After major game updates, recoil and sensitivity values may shift; check the changelog for updates and retune in a private match as needed.
Setup Guide
- Follow these steps to get Killer v1.1 running on your Cronus Zen for Call Of Duty. 1. Ensure your Cronus Zen firmware is up to date and the device is recognized in Zen Studio. 2. Download Killer v1.1 and open the script file in Zen Studio. 3. Load Killer v1.1 into an open slot (slot 1 recommended) and save the configuration to your device. 4. Connect your controller and verify the device LED indicates the correct slot is active. 5. Apply recommended in-game settings for Call Of Duty before enabling any mods or macros. 6. Start with default values and enter a private match or training mode to establish a baseline. 7. Enable one feature at a time and run a 5-minute validation session before adding more. 8. Fine-tune sensitivity and strength sliders based on your playstyle and in-game feel.
Best Settings for Call Of Duty
For best results with Killer v1.1 in Call Of Duty, use mid-range in-game sensitivity (typically 5-7 or equivalent) and match your controller deadzone to the script's expectations. Apply the recommended Zen Studio slot configuration before loading the script.
Tuning Guide
| Feature | When To Adjust | Expected Effect |
|---|---|---|
| Weapon Profiles | After baseline setup | Improves control consistency |
| Weapon Tracking | After baseline setup | Improves control consistency |
| Macro Profiles | After baseline setup | Improves control consistency |
| Timing Profile | After baseline setup | Improves control consistency |
| Anti Recoil | After baseline setup | Improves control consistency |
| Rapid Fire | After baseline setup | Improves control consistency |
Tips for Best Results
- Run a 5-10 minute warm-up in training mode before jumping into matches. Keep a note of your preferred values so you can restore them after updates. Test one feature at a time when first configuring; avoid enabling everything at once. Match your in-game sensitivity to the script's recommended range for best results. After a game patch, retune in a private match before using in ranked or competitive play. Use the same controller and cable consistently to avoid input variance.
Troubleshooting
Script not triggering
Ensure the correct Zen slot is active and the script is compiled in Zen Studio. No response after connecting | Check all USB connections and ensure Cronus Zen firmware is up to date. Behavior feels inconsistent | Retune in a private match after any game update. Device not recognized | Reinstall Zen Studio drivers and reconnect the device. Input lag or delayed response | Use a shorter USB cable and connect directly to the console.
Changelog
- 2026-02-22: Published profile refresh for Latest Season.
- 2026-03-06: Validation run completed with latest test checklist.
Frequently Asked Questions
Is Killer v1.1 compatible with the latest Call Of Duty patch?
Current compatibility target is Latest Season.
Which setting should I tune first?
Start with anti-recoil and aim behavior before enabling additional macros.
Trust and Support
- [object Object]
- [object Object]
- [object Object]